方管

  镀锌方管跟焊接钢管主要区别
  这是方管制造过程的一个重要环节
  Q345B方管高频焊接工艺
  焊管常用材质为:Q235A,Q235C
  方管型号/方管理论重量表
  大口径厚壁方管常见规格表
  如何来延长方管的使用寿命?
  镀锌方管存放和采购应要注意的事项
  当前位置 -> 行业资讯- 怎样维护才能使【翅片管】的寿命更长呢? 发布时间:(2018/11/6)

怎样维护才能使【翅片管】的寿命更长呢?


很多用户都对翅片管使用过程中发现有些翅片管的保养不注意导致使用年限短提出了-怎样维护才能使翅片管的寿命更长呢 这些问题,今天我给大家整理了下以下注意事项:翅片管是通过高频焊接技术加上鳞片状翅片,所以安装使用中切勿碰撞挤压,这样会容易变形,更甚者影响散热效果。
Many users have found that some of the finned tubes are not carefully maintained, which leads to short service life. How to maintain the finned tubes to make their life longer? Today, I have tidied up the following points for attention: Finned tubes are installed through high frequency welding technology plus flaky fins. Do not impact extrusion during use, so it will be easy to deform, and even more affect the cooling effect.
因为翅片管鳞片螺旋分布,长期使用中会有一些沉淀物及水锈层等,我们要及时清洗打扫。
Because of the spiral distribution of finned tube scales, there will be some sediments and rust layer in long-term use, so we need to clean in time.
翅片管借口处检查接口处是否松动和脚垫脱落。
Finned tube excuses check whether the interface is loose and the pads fall off.
翅片管暴露在外面的地方避免雨水低落,尽量保持干燥,距离地面不宜太近,避免温室大棚内灌溉腐蚀了翅片管。
The finned tube should be exposed to the outside to avoid falling rain, keep as dry as possible, not too close to the ground, so as to avoid the erosion of the finned tube by irrigation in greenhouse greenhouse.
通过对翅片管的保养,翅片管的使用年限上会有很大的增长。任何一件物品的长久使用都离不开用心的保养和维护,翅片管也不例外,那么具体要从哪些方面来对翅片管保养维护呢?我们看看翅片管网专家给的介绍。
Through the maintenance of finned tubes, the service life of finned tubes will increase greatly. The long-term use of any item can not be separated from careful maintenance and maintenance, and fin tube is no exception, so from what specific aspects to maintain fin tube? Let's look at the introduction of finned pipe network experts.
1、定期检查各翅片管无锡清洗是百炼成仙否完善,是否有沉积物、结焦、水锈层等结垢附着,并即时进行清洗。在这同时还必须检查各翅片管与橡胶垫圈的粘合是否紧密,橡胶垫圈本身是否完好,以免橡胶垫圈脱胶与损坏而引起的漏泄。
1. Check regularly whether the finned tube Wuxi cleaning is perfect or not, whether there are deposits, coking, rust layer and other fouling adherence, and immediately clean. At the same time, it is necessary to check whether the finned tubes are closely bonded to the rubber gasket and whether the rubber gasket itself is in good condition, so as to avoid leakage caused by rubber gasket degumming and damage.
2、板式热交换器压紧螺帽与上下导杆,应经常武动乾坤加润滑油脂进行润滑。
2. Plate heat exchanger pressure nuts and upper and lower guide rods should be often used to add lubricating grease to lubricate.
3、各仪表调节应有专人负责,并严格执行操作规程进行操作与维护。
3, the instrument adjustment should be specially responsible, and strictly enforce the operation rules for operation and maintenance.
4、当需更换的橡胶垫圈或修补脱胶部分时,需将该翅片管取下,放在桌上,将旧垫圈拆下,或在脱胶处将翅片管凹槽的胶水遗迹用细砂纸擦尽,再用四氯化碳或三氯乙 烯等溶剂把凹槽内的油迹擦尽,再把新橡胶的垫圈的背部用细砂纸擦毛,同样用四氯化碳或三氯乙烯溶剂把油迹擦尽。然后在凹槽和橡胶垫圈背面均薄薄敷上一层胶 水,待稍干一下,以不粘手指,但仍发粘为度,即将橡胶垫圈嵌入槽内,四周压平,敷一层滑石粉,随即将翅片管装上设备机架轻轻夹紧。根据胶水说明书要求隔大 周皇族一段时间即可投产使用。
4. When replacing the rubber washer or repairing the degumming part, the finned tube should be removed and placed on the table. The old washer should be removed, or the glue vestiges of the groove of the finned tube should be rubbed out with fine sandpaper at the degumming place. The oil traces in the groove should be rubbed out with carbon tetrachloride or trichloroethylene, and the back of the new rubber washer should be used. Fine sand paper is used to rub hair, and the oil stains are also wiped out with carbon tetrachloride or trichloroethylene solvent. Then apply a thin layer of glue on the back of the groove and rubber washer, wait for a little drying, in order not to stick fingers, but still stick, that is, rubber washer is embedded in the groove, flat around, coated with a layer of talcum powder, and then the finned tube is installed on the equipment rack and lightly clamped. According to the requirements of the glue instruction, the royal family can be put into operation for a period of a week.
5、每次将翅片管重新压紧时,须注意上一次压紧时的刻度位置,切勿使橡胶垫圈压过度,以致降低垫圈使用寿命。
5. Every time the finned tube is re-compressed, attention should be paid to the calibration position of the last compression, so as not to overpress the rubber washer, so as to reduce the service life of the washer.
6、更换翅片管橡胶垫圈时,须将该段全部更新,以免各片间隙不均,影响传热效果。
6. When replacing rubber gaskets of finned tubes, all the sections should be updated so as to avoid uneven clearance between the finned tubes and affect the heat transfer effect. 专家表示说:一般在操作开始使用清水进行循环时,可能有轻微的漏泄,到温度升到杀菌温度时,漏泄将自行消失。如果漏泄仍不停止,须将翅片管再压紧一些。如果仍不见效,尚须打开检查橡胶垫圈的情况,亦有可能是翅片管末按片上号码顺序排列,则应予纠正。
Experts said: Generally, when the operation begins to circulate with clean water, there may be a slight leakage. When the temperature rises to sterilization temperature, the leakage will disappear by itself. If the leakage does not stop, the finned tube must be pressed further. If it is still ineffective, it is necessary to open the rubber washer to check the situation, or it is possible that the fin tube end is arranged in the order of on-chip number, it should be corrected.辛苦整理.转载请注明http://www.wxsxsjx.com

方管

版权所有@转载请注明:http://www.wxxsygg.com/shownews.asp?id=2077
相关阅读:今日早盘国内方管价格惯性续弱与昨持平 | 11月6日无锡市场方管价格行情延续弱势 | 贸易摩擦升温方管行业如何应对?
本站网址:http://www.wxxsygg.com 来源:鑫盛源方管  浏览次数:38 
 
 
网站导航 | 方管厂家介绍 | 方矩管展示 | 方管知识 | 方管规格 | 销售网络 | 价格行情 | 客户留言 | 方管销售电话 | 博客
地图 Sitemap 方管